12/27/2023 0 Comments Ipass black power voltage![]() ![]() ![]() I attach my configuration.h ( Configuration.h ) hoping someone help me to resolve this problem and sorry again for my english.Įdited 1 time(s). Leave commented only this line: //#define ENDSTOPPULLUP_ZMINīut nothing to do, the problem still exist. Then, since the problem wasn't solved, i tried to uncommented these lines: I use the Marlin RC7 firmware and I have made that changes for the autobed leveling: I try to search in the posts on this forum the answer for my question but I could not find it. I think that is a firmware problem, but I haven't idea what's the cause. If I don't stop with the "STOP button" on Repetier-host, the extruder continues to go down untill touch and break the glass over the heated bed. My problem is: when I type G29 the X and Y axis go to home perfectly, instead the Z axis goes down without stopping when the led turns on. PWCD,US,NEMA5-15P TO IEC60320 C13,6FT,14AWG,15A,125V,RoHS/REACHĬBL,FRONT CNTL,16 TO 16 PIN,RA,RND TUBE,24CM,28AWGĨ0x80x38 mm, 10.5K RPM, Optional Middle Cooling Fan for X10 2U Ultra and HFT Series Servers,RoHS/REACHīlack gen-3 hot-swap tool-less 2.5- inch HDD trayīlack gen-3 2.5 NVMe drive tray, Orange tab with lock (improved EMI for hotswap NVMe drive)ģ6" Rail set for Auto-latch, quick/quick, 2, 3U 17.Brown wire to power supply and blue and black wires to the ZMIN on the ramps 1.4 and the sensor works, because if I pass below the sensor, an alluminium foil, the sensor turns on. Plastic air shroud for SC829U, 219U (X11 24DIMM, right side)ĢU Ultra Riser Card with 4 NVME and PCI-Ex16,RoHS/REACHġU Ultra RHS Riser Card with 1 PCIE/SATA Hybrid M.2 &1 PCIEĢU Passive CPU Heat Sink for X11 Purley Platform Equipped with a Narrow Retention MechanismĪC-DC 1600W, Titanium Level, Redundancy, 1U, DC Output: +12V and +12Vs, 203 x 73.5 x 40 mm, AC Input: 90 - 264 VAC/47-63Hz, PMBus 1.2 with DSP controller,HF,RoHS/REACHĤ PIN MIDDLE FAN POWER CABLE (PWM). Plastic air shroud for SC829U, 219U (X11 24DIMM, left side) 1.0,INT,PCIe NVMe SSD, 85CM,34AWG,RoHS/REACH OCuLink v 1.0,INT,PCIe NVMe SSD, 65CM,34AWG,RoHS/REACH PCIe Gen3x16 input to PLX9765 to support 12x NVMe portĢ-port 2U SAS3 12Gbps backplane, support up to 2x 2.5-inch SAS3/SATA3 HDD/SSDĨ pin female to 4 pin female power, 37cm, 18AWG,RoHS/REACH 2 M.2 PCI-E 3.0 x4 M-Key NVMe (2260/2280/22110) via optional add-on card AOC-SLG3-2M2ġ600W Redundant Power Supplies with PMBusĢU Ultra Riser with 4-port 10GbE RJ45 (10GBase-T).24 Hot-swap 2.5" drive bays: 24 NVMe (4 hybrid ports - SAS3 via opt.See manual block diagram and AOC Support for details.) (Both CPUs need to be installed for full access to PCI-E slots and onboard controllers. Monitoring for CPU and chassis environment.Pulse Width Modulated (PWM) fan connectors.Monitors for CPU Cores, Chipset Voltages, Memory.IPMI 2.0 with virtual media over LAN and KVM-over-LAN support.Support for Intelligent Platform Management Interface v.2.0.1x Realtek RTL8211E PHY (dedicated IPMI).4x 10GBase-T ports via Intel® X550 Ethernet Controller.SATA3 (6Gbps) RAID 0, 1, 5, 10 per node.Contact your Supermicro sales rep for more info. † 2933MHz in two DIMMs per channel can be achieved by using memory purchased from Supermicro Up to 6TB 3DS ECC DDR4-2933MHz † RDIMM/LRDIMM.Or above is required to support 2nd Gen Intel® Xeon® Scalable processors (codenamed Cascade Lake-R) 2nd Gen Intel® Xeon® Scalable Processors and Intel® Xeon® Scalable Processors ‡,.Please contact sales-rep for alternative options. (with minimum 2 CPUs, 4 DIMMs and 6 U.2 NVMe).ĭrivers & Utilities BIOS IPMI Tested Memory Tested M.2 List NVMe Options Manuals OS Certification Matrix Compatible GPU List Quick-References Guide Drive Options Network Card (AOC) Matrix Data Center Solution Engineering (DCSE)Ĭomplete System Only: To maintain quality and integrity, this product is sold only as a completely-assembled system.Server quality, built for gaming – SUPERO systems by Supermicro are optimized for high performance and reliability, providing options for gamers at all levels ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |